Besides, by doing necessary adjustments in the weights you can create a FADE or DRAW bias whatever you want. This will put a high trajectory on the balls to give you a perfect shot. Now, you can also move back both of the weights and can also split them. If you are among the players who don’t strike the ball at the center of the face, this setting is for you. This setting is good for creating a penetrating flight.
![taylormade driver burner series taylormade driver burner series](https://image.globalgolf.com/dynamic/1001164/aaa/sku/1001164-aaa.jpg)
If you push both of the weights far forward towards the face, the spin will be reduced. You can loosen or tighten by using the same wrench. That is why the center of gravity will be three times more than an M1 driver. Now, unlike an M1 head that has a T shape weight track, the M3 driver has a Y shape weight track. As you already know, there are two movable 11-gram weights in the sliding rails which can be adjusted as per your requirement. Adjustments at the Head:Īt this point, you can also do adjustments in the head of the driver. While this confirms a draw, it’s more subtle than the traditional higher setting. Now, the loft will be at the stated number, however, the club will be at 4 degrees upright than the standard position. To do that, you have to rotate the tip adaptor through the whole 180 degrees to the UPRT position. You’ll find the notches at the tip of the shaft, where you can make incremental adjustments and in this case, the change will be more gradual. For example, if you don’t want to adjust exactly to the higher or lower position, the driver has a more innovative option for you. Now, the M3 driver has so many options for making the adjustments. Besides, the face will be at 4 degrees closer position and the face angle will be 58 degrees, but the driver will add at least 400 RPM spin to the ball. On the other hand, if you adjust the shaft at a higher position than the standard, the loft size will become 11 degrees. On top of that, the spin will be reduced by 400 RPM, so less spin will be applied to the ball by the driver. Besides, you’ll get the face at least 4-degrees more open, leaving the lie angle at 58-degrees. Now, if you rotate the shaft to the lower position, it will make the loft 7 degrees. In this case, the face angle will be square. For your instance, if you lock in the STD loft, for a 9-degreed driver, you’ll have a loft of straight 9 degrees, while the lie angle will be found as 56 degrees which are the standard.
#Taylormade driver burner series plus#
The Taylormade comes with a 4-degreed tip adapter, so you can change in the standard loft and adjust it for plus or minus two degrees. This is the most important area to make adjustments to Taylormade M3. After getting the fully opened shaft in your hand, you will see some settings and numbers on the tip position of the shaft. So, turn the wrench anti-clockwise, it will remove the screw and you will be able to open up the head from the shaft. Now, you need to remove the head from the shaft, right? Remember one thing, you will hear an audible click sound if you reach the threshold level of tightening. You must use the wrench on the top of the screw and turn it to the necessary direction for doing your required task.įor instance, if you turn the wrench clockwise it will tighten the screw. Now, you need a simple housekeeping wrench to get the job done.
#Taylormade driver burner series how to#
Opening the Shaft:įirst of all, you need to know how to open up a screw to remove the head from the shaft.
![taylormade driver burner series taylormade driver burner series](https://cdn2.bigcommerce.com/n-pktq5q/ghg13z/products/20316/images/825489/26291a-taylormade-burner-460-driver-105-degrees-graphite-reax-stiff-flex-26261a__86671.1506967186.1280.1280.png)
To adjust an M3 driver you can simply follow these steps.
![taylormade driver burner series taylormade driver burner series](https://cdn2.bigcommerce.com/n-pktq5q/ghg13z/products/21102/images/829693/27247a-taylormade-burner-driver-ht-13-deg-graphite-reax-50-ladies-flex-27247a__96095.1506974022.1280.1280.jpg)
Whether raising or lowering the loft, making the bias draw or fade, or making necessary adjustments in the spin or trajectory of the driver to the ball has become easier than ever with this highly adjustable M3 driver. You just need a simple wrench to make your necessary adjustments on this driver. The M3 driver is technologically advanced and has a twist face and also a hammerhead slot. Final Words How to Adjust Taylormade M3 Driver Properly